English      KOI8-RU

US Robotics Total Control
NETServer 4.2.0

Аппаратные настройки

См. Аппартные настройки в описании NETServer 3.2.5.92

Опознание версии

Подключите консольный кабель одним концом к порту "Console" и вторым концом к терминалу VT100 (или нульмодемный консольный кабель - к последовательному порту компьютера и запустите на нем терминальную программу). Включите NETServer. Через несколько секунд на экране терминала появится текст, в котором есть строка с версией программы:
NetServer 8/16 Application Loader Is Running...


Initializing the FLASH file system.

Uncompressing file: ns816.bin.z
Initializing decompression module.

In : 2102042 bytes
--10--20--30--40--50--60--70--80--90--100

¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦¦
Completed uncompressing the iнNetServer 8/16 kernel is running...


       Network Products Corporation (Pasadena, CA) All rights reserved.
AppleTalk-compatible networking software is Copyright 1993-1995,
       Quiotix Corporation (Menlo Park, CA) All rights reserved.
TCP/IP networking software is Copyright 1988-1995,
       Epilogue Corporation, Albuquerque NM, All rights reserved.
IP routing software is Copyright 1993-1995,
       RainbowBridge Communication. Inc. Rockville MD, All rights reserved.
IPX networking software is Copyright 1994-1995,
       RouterWare Inc. Newport Beach CA, Unpublished - rights reserved
       under the Copyright Laws of the United States.
VJ TCP Header Compression software is Copyright (c) 1989, 1991, 1992, 1993,
       Regents of the University of California. All rights reserved.


Netserver, V4.2.0
3Com/U. S. Robotics Access Corporation, Skokie Illinois
    The Intelligent Choice in Information Access

The software contained in this product is
    Copyright 1996, US Robotics Access Corporation, Skokie Illinois
    All rights reserved.


Allocated 2022400 bytes of memory for RoboExec
Starting up the Netserver system Executive...
Starting up Netserver Configuration process...

Netserver Configuration Process starting......

Netserver starting required processes......

Netserver configuring interfaces......

Netserver configuring networks......

Netserver Adding networks to LAN interfaces....

Netserver enabling networks on LAN interfaces....

Configuring Network Services.....

Starting the CLI......
Command Line Interpreter Started - Please Wait...

Configuring default Network Services (telnet and tftp.....
At 16:35:56, Facility "Configurator", Level "INFORMATION":: Netserver system configuration complete at 9/11/1999 16:35:56
netserver>

Первичная настройка

Сброс старых настроек

Чтобы стереть предыдущие настройки (в том числе пароль): Включите четвертый переключатель в колодке "NETServer configuration" (положение "ON", нижнее) и перезагрузите NETServer (выключите питание и снова включите). После завершения загрузки верните переключатель в обратное положение ("OFF", верхнее) чтобы при следующей загрузке настройки сохранились.

Настройка NETServer (вручную)

Подключите консольный кабель к порту "Console". NETServer по завершению загрузки выведет:
netserver>_QuickNetServer
netserver>Welcome to the Netserver Quick Setup


The Netserver Quick Setup will let you set up simple configuration
for your whole system or different portions of the system.

Do you want to continue with Netserver Quick Setup? y

 There are two ways to proceed: You can set up only the basic
configuration, which will allow you to continue with the Windows-based
Netserver Manager Plus. Or you can configure a simple configuration
for IP, IPX, and AppleTalk.

Do you want to configure only enough to use the GUI based system [yes]?
Введите yes (не обязательно) и нажмите "Enter". Затем отвечайте на вопросы программы, приблизительно так, как я это делал в следующем примере:
Quick Setup Identification information
--------------------------------------
>>> Enter the name of your system []: ns8
>>> Who is the system contact person []? Grumbler 
>>> Where is this system located []? Ekaterinburg

Quick Setup Management information
----------------------------------

The GUI-based management system uses SNMP to communicate with the Netserver.

An SNMP community names a group of systems that can manage
your system via SNMP. It is a rudimentary form of security.
>>> What SNMP community will manage this system [public]? private
>>> What is the address of the management station [0.0.0.0]? 172.16.0.129

Quick Setup IP information
--------------------------

The Netserver uses a network name to identify the network for
future management commands.
>>> Enter the network name of your IP network [ip]: grumbler.pvt

>>> Enter the IP address for the Netserver []: 172.16.0.9

The IP mask can be specified as a class ("A", "B", or "C"),
the number of one bits in the mask, or as an address in the format
255.x.x.x
>>> What should the mask be set to [C]?

>>>Do you want to set up a default gateway [yes]?

The default gateway gives the address of a router that the Netserver
will forward packets to when it has no other route to their destination.
It cannot be the same address as the IP address for the Netserver
>>> Enter the IP address of the default gateway []? 172.16.0.1

The metric or "hop count" tells the Netserver how far the default
router is from the Netserver.
>>> What metric should be applied to the default gateway [1]?
IP setup is completed.

Would you like to review your current settings before executing [yes]?
Identification Information:
   System Name:                  ns8
   System Contact:               Grumbler 
   System Location:              Ekaterinburg
Management Information:
   SNMP Management:
      SNMP Community:            private
      SNMP IP Address:           172.16.0.129
      SNMP Read&Write:           yes
IP Information:
   IP Network Name:              grumbler.pvt
   IP Network Address:           172.16.0.9
   IP Mask:                      C
   IP Frame Type:                ethernet_ii
   IP Def Gateway Addr:          172.16.0.1
   IP Def Gateway Metric:        1
   TFTP Client Information:
      TFTP Access:               Only: 172.16.0.129

Do you want to change any answers [no]?

Do you want to actually execute these commands [yes]?
DO /./QuickSetup.cfg
netserver>
netserver>netserver>set system name "ns8"
netserver>set system location "Ekaterinburg"
netserver>set system contact "Grumbler "
netserver>add snmp community private address 172.16.0.2 access RW
netserver>disable security_option remote_user_administration telnet
netserver>add ip network "grumbler.pvt" interface eth:1 address 172.16.0.9/C frame ethernet_ii enable no
netserver>enable ip network "grumbler.pvt"
netserver>add ip defaultroute gateway 172.16.0.1 metric 1
netserver>add tftp client 172.16.0.2
netserver>save all
Saving..... SAVE ALL
Saving..... SAVE ALL
Saving..... SAVE ALL
SAVE ALL  Complete
netserver>Spawned Process CFP 2c2002   /./QuickSetup.cfg Completed Successfully
Теперь первичная настройка завершена и NETServer готов к конфигурированию с консоли (или программой по сети). В командной строке консоли можно ввести HELP для просмотра справки по командам.

Настройка NETServer (GUI/автоматическая)

Теперь первичная настройка завершена и NETServer готов к конфигурированию программой "NETServer Manager Plus" по сети (использует протокол SNMP).

Изменение некоторых настроек

Замена адреса IP

Нужно выполнить последовательность команд: disable ip network "network name"
delete ip network "network name"
add ip network "network name" address [new_ip_address]/24 frame ethernet_ii enable yes
save all
Для контроля можно использовать команду "show network".

Пример.

netserver>show ip network "ip"

SHOW IP  NETWORK ip SETTINGS:
Interface:                                 eth:1
Network Address:                           172.16.0.9/C
Frame Type:                                ETHERNET_II
Status:                                    ENABLED
Reconfigure Needed:                        FALSE
Mask:                                      255.255.255.0
Station:                                   172.16.0.9
Broadcast Algorithm:                       1
Max Reassembly Size:                       3468
IP Routing Protocol:                       NONE
IP RIP Routing Policies:
IP RIP Authentication Key:

netserver>disable ip network "ip"
netserver>delete ip network "ip"
netserver>add ip network "ip" address 172.16.0.8/24 frame ethernet_ii enable yes
netserver>save all
Saving..... SAVE ALL
SAVE ALL  Complete
netserver>show ip network "ip"

SHOW IP  NETWORK ip SETTINGS:
Interface:                                 eth:1
Network Address:                           172.16.0.8/C
Frame Type:                                ETHERNET_II
Status:                                    ENABLED
Reconfigure Needed:                        FALSE
Mask:                                      255.255.255.0
Station:                                   172.16.0.8
Broadcast Algorithm:                       1
Max Reassembly Size:                       3468
IP Routing Protocol:                       NONE
IP RIP Routing Policies:
IP RIP Authentication Key: